Intel S5520SC Specifikace Strana 132
- Strana / 192
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Jumper Blocks Intel® Workstation Board S5520SC TPS
Revision 1.7
Intel order number: E39530-010
118
Jumper Name Pins System Results
2-3
The main system BIOS will not boot with pins 2-3 connected. When connected, the system
will only boot from EFI-bootable recovery media with a recovery BIOS image present.
J1H1: Force BMC
Update
1-2 BMC Firmware Force Update Mode – Disabled (Default)
2-3 BMC Firmware Force Update Mode – Enabled
J2C1: CMOS Clear
1-2 These pins should be connected for normal system operation. (Default)
2-3
If connected and AC power unplugged, the CMOS settings will clear in 5 seconds. The 2-3
pins should not be connected for normal system operation.
J4B2: Serial Port A
Configuration
1-2 Rear RJ-45 Serial A port is configured for DSR to DTR. (Default)
2-3 Rear RJ-45 Serial A port is configured for DCD to DTR.
7.1 CMOS Clear and Password Reset Usage Procedure
The CMOS Clear (J2C1) and Password Reset (J1E4) recovery features are designed so the
needed operation is achieved with minimum system down time. The usage procedure for these
two features has changed from previous generation Intel
®
workstation boards. The following
procedure outlines the new usage model.
7.1.1 Clearing the CMOS
1. Power down the workstation and unplug the power cord.
2. Open the workstation chassis. For instructions, refer your workstation chassis
documentation.
3. Move jumper (J2C1) from the default operating position (covering pins 1 and 2) to the
reset/clear position (covering pins 2 and 3).
4. Wait five seconds.
5. Move the jumper back to default position (covering pins 1 and 2).
6. Close the workstation chassis and reconnect the AC power cord.
7. Power up the workstation.
The CMOS is now cleared and you can reset it by going into the BIOS setup.
7.1.2 Clearing the Password
1. Power down the workstation. Do not unplug the power cord.
2. Open the chassis. For instructions, refer your workstation chassis documentation.
3. Move jumper (J1E4) from the default operating position (covering pins 1 and 2) to the
password clear position (covering pins 2 and 3).
4. Close the workstation chassis.
5. Power up the workstation and then press <F2> to enter the BIOS menu to check if the
password is cleared.
6. Power down the workstation.
7. Open the chassis and move the jumper (J1E4) back to its default position (covering pins
1 and 2).
- Workstation Board S5520SC 1
- Revision History 2
- Disclaimers 3
- Table of Contents 4
- List of Figures 9
- Revision 1.7 10
- List of Tables 11
- 1. Introduction 15
- 2. Overview 16
- Overview 19
- 3. Functional Architecture 30
- 3.1 Intel 31
- 5520 I/O Hub (IOH) 31
- 3.2 Processor Support 32
- 3.2.3 Intel 34
- Technology (EIST) 34
- 3.3 Memory Subsystem 36
- 3.3.2 Supported Memory 38
- 3.3.5 Memory Interleaving 42
- 3.3.6 Memory Test 43
- 3.3.7 Memory Scrub Engine 43
- 3.3.8 Memory RAS 43
- Tables 5 and 6 47
- 3.4 ICH10R 49
- Revision 1.7 50
- 3.5 PCI Subsystem 52
- 3.6 Intel 53
- 3.6.1 SAS RAID Support 54
- 3.8 Serial Ports 57
- 3.9 Floppy Disk Controller 58
- 3.11 Video Support 58
- 3.11.1 Video Modes 59
- 3.11.2 Dual Video 59
- 3.13 Audio Codec 62
- 3.14 IEEE 1394a Support 63
- 3.15.1 Overview 64
- 3.15.2 TPM security BIOS 64
- 3.16 ACPI Support 67
- 3.17 Intel 67
- Virtualization Technology 67
- 4. Platform Management 68
- 4.2.3 Media Redirection 71
- 4.2.5 Embedded Web server 73
- 4.3 Platform Control 74
- 4.3.2 Fan Speed Control 75
- 4.4 Intel 78
- 5. BIOS Setup Utility 80
- 5.3.1 Operation 81
- 5.3.2.1 Main Screen 84
- 5.3.2.2.1 Processor Screen 87
- 5.3.2.2.2 Memory Screen 90
- 5.3.2.2.6 PCI Screen 98
- Revision 1.7 103
- 5.3.2.6 Boot Options Screen 108
- 6.2 Power Connectors 119
- 6.3.1 Intel 121
- RMM3) Connector 121
- 6.3.2 LCP/IPMB Header 121
- 6.4 Front Panel Connector 122
- 6.5 I/O Connectors 123
- 6.5.3 SAS Module Slot 124
- 6.5.5 USB Connector 125
- 6.5.6 IEEE 1394a connectors 127
- 6.6 Audio Connectors 128
- 6.7 Onboard Video Header 128
- 6.8 Fan Headers 129
- 7. Jumper Blocks 131
- 7.1.1 Clearing the CMOS 132
- 7.1.2 Clearing the Password 132
- 7.3 BIOS Recovery 133
- 8. Intel 135
- Light Guided Diagnostics 135
- 8.2 Fan Fault LEDs 136
- A. System Status LED 137
- B. System ID LED 137
- 8.4 DIMM Fault LEDs 139
- 9.1 Intel 141
- 9.2 MTBF 141
- Table 76. MTBF Estimate 142
- Revision 1.7 144
- 9.4.1 Grounding 145
- 9.4.2 Stand-by Outputs 146
- 9.4.3 Remote Sense 146
- 9.4.4 Voltage Regulation 146
- 9.4.5 Dynamic Loading 147
- 9.4.6 Capacitive Loading 147
- 9.4.7 Ripple/Noise 147
- 9.4.8 Timing Requirements 148
- Table 84. Turn On/Off Timing 149
- FCC (USA) 153
- ICES-003 (Canada) 155
- VCCI (Japan) 155
- BSMI (Taiwan) 155
- RRL KCC (Korea) 156
- 10.7 CA Perchlorate Warning 159
- Appendix B: Compatible Intel 162
- Server Chassis 162
- POST Error Beep Codes 185
- Glossary 188
- Reference Documents 192
Související produkty a manuály pro Základní desky serveru / pracovní stanice Intel S5520SC
(88 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce