Intel SG-81 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Hardware Intel SG-81. Intel SG-81 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - SG-80 Series

SG-80 Series (SG-80, SG-81) Intel Pentium 4 System Board Socket 775 User’s Manual Rev. 1.00

Strany 2

1-6 Chapter 1 SG-80 Series

Strany 3 - Table of Contents

Hardware Setup 2-1 Chapter 2. Hardware Setup 2.1. CPU Socket This server board provides one 775-pin Zero Insertion Force (ZIF) socket to install the

Strany 4

2-2 Chapter 2 2.2. System Memory This system board provides two 184-pin DDR DIMM slots for un-buffered and non-ECC modules with memory size expansible

Strany 5 - Chapter 1. Introduction

Hardware Setup 2-3 2.3. Connectors, Headers, and Switches All the connectors, headers and switches mentioned here are depending on your system confi

Strany 6 - Product List

2-4 Chapter 2 2.3.2. FAN Connectors (CPUFAN, SYSFAN, PWRFAN) These connectors each provide power to the cooling fans installed in your system. • CPU

Strany 7 - 1.2. Layout Diagram (SG-80)

Hardware Setup 2-5 2.3.3. CMOS Memory Clearing Header (CCMOS) This header uses a jumper cap to clear the CMOS memory. • Pin 2-3 shorted (default):

Strany 8 - 1.3. Layout Diagram (SG-81)

2-6 Chapter 2 2.3.4. Front Panel Switches & Indicators Connection Headers (PANEL1) These headers are used for connecting switches and LED indicat

Strany 9

Hardware Setup 2-7 2.3.5. Additional USB Port Connection Header (USB3, USB4) These headers each provide 2 additional USB 2.0 ports connection throug

Strany 10 - 1-6 Chapter 1

2-8 Chapter 2 2.3.6. Front Panel Audio Connection Header (FPIO-AUDIO1) This header provides the connection to audio connector at front panel. • To u

Strany 11 - Chapter 2. Hardware Setup

Hardware Setup 2-9 2.3.7. Accelerated Graphics Port Slot (AGP1) This slot supports an optional AGP graphics card up to AGP 8X/4X mode. ATTENTION: Th

Strany 12 - 2.2. System Memory

Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the

Strany 13

2-10 Chapter 2 2.3.8. Internal Audio Source Connectors (CD1, AUX1) These connectors connect to the audio output of internal CD-ROM drive or add-on ca

Strany 14

Hardware Setup 2-11 2.3.9. Floppy Disk Drive Connector (FDC) This connector supports two standard floppy disk drives via a 34-pin 34-conductor ribbo

Strany 15

2-12 Chapter 2 2.3.10. IDE Disk Drive Connectors (IDE1, IDE2) These IDE ports each connects up to two IDE drives at Ultra ATA/100 mode by one 40

Strany 16 - (PANEL1)

Hardware Setup 2-13 2.3.11. Serial ATA connectors (SATA1, SATA2) These connectors are provided to attach one Serial ATA device at each channel via S

Strany 17

2-14 Chapter 2 2.3.12. External I/O Panel • Mouse: PS/2 mouse connector. • Keyboard: PS/2 keyboard connector. • LPT1: Parallel port connector. •

Strany 18

BIOS Setup 3-1 Chapter 3. BIOS Setup 3.1. About the Setup Utility The computer uses the latest Award BIOS with support for Windows Plug and Play. T

Strany 19

3-2 Chapter 3 3.1.2. Entering the Setup Utility When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of

Strany 20 - 2-10 Chapter 2

BIOS Setup 3-3 3.1.3. Updating the BIOS You can download and install updated BIOS for this motherboard from the manufacturer’s Web site. New BIOS pr

Strany 21

3-4 Chapter 3 3.2. Using BIOS When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the optio

Strany 22

BIOS Setup 3-5 IDE Devices (None) Your computer has two IDE channels (Primary and Secondary) and each channel can be installed with one or two device

Strany 23 - User’s Manual

Table of Contents Chapter 1. Introduction ... 1-1 1.1. Features & Specifications...

Strany 24 - 2.3.12. External I/O Panel

3-6 Chapter 3 Refer to your drive’s documentation or look on the drive casing if you need to obtain this information. If no device is installed, chang

Strany 25 - Chapter 3. BIOS Setup

BIOS Setup 3-7 3.2.2. Advanced BIOS Features This option defines advanced information about your system.  CPU Feature Scroll to this item and pres

Strany 26

3-8 Chapter 3 Thermal Management This item displays CPU’s temperature and enables you to set a safe temperature to Prescott CPU. TM2 Bus Ratio This it

Strany 27 - 3.1.3. Updating the BIOS

BIOS Setup 3-9 CPU L3 Cache (Enabled) This item is only available when processors support L3. Some high-end processors support L3. If the CPU do supp

Strany 28 - 3.2. Using BIOS

3-10 Chapter 3 ATA 66/100 IDE Cable Msg. (Enabled) This item enables or disables the display of the ATA 66/100 Cable MSG. Security Option (Setup) If y

Strany 29

BIOS Setup 3-11  DRAM Clock/Timing Control: Scroll to this item and press <Enter> to view the following screen: DRAM Timing Control Enables y

Strany 30

3-12 Chapter 3  RAS to CAS Delay (tRCD): This is the amount of time a CAS is performed after a RAS. The lower the better, but some DRAM does not sup

Strany 31 -  CPU Feature

BIOS Setup 3-13 AGP Data Rate (Auto) This item allows users to set the AGP Data Rate by, Auto, 1X, 2X, 4X, or 8X, depending on what speed the AGP car

Strany 32 -  Hard Disk Boot Priority

3-14 Chapter 3 3.2.4. Integrated Peripherals These options display items that define the operation of peripheral components on the system’s input/outp

Strany 33

BIOS Setup 3-15 Internal PCI/IDE (Both) Use these items to enable or disable the internal PCI IDE channels that are integrated on the mainboard. IDE

Strany 34

3.2. Using BIOS ... 3-4 3.2.1. Standard CMOS Features ...

Strany 35 -  DRAM Clock/Timing Control:

3-16 Chapter 3  OnChip PCI Device Scroll to this item and press <Enter> to view the following screen: OnChip USB Controller (Enabled) Enable t

Strany 36

BIOS Setup 3-17 Press <Esc> to return to the Integrated Peripherals screen.  Onboard SuperIO Device: Scroll to this item and press <Enter&g

Strany 37 -  OnChip AGP Control

3-18 Chapter 3  ECP Mode Use DMA (3) When the onboard parallel port is set to ECP mode, the parallel port can use DMA3 or DMA1. Press <Esc> to

Strany 38 -  OnChip IDE Device

BIOS Setup 3-19  Resume by USB from S3 (Disabled) When set to Enabled, the system power will resume the system from a power saving mode if there is

Strany 39

3-20 Chapter 3 [Power Off]: When power returns after an AC power failure, the system’s power remains off. You must press the Power button to power-on

Strany 40 -  OnChip PCI Device

BIOS Setup 3-21 If you cannot get a legacy ISA (Industry Standard Architecture) expansion card to work properly, you might be able to solve the probl

Strany 41 -  Onboard SuperIO Device:

3-22 Chapter 3 PIRQ_0 Use IRQ No. ~ PIRQ_7 Use IRQ No. [Auto] This item specifies the IRQ number manually or automatically for the devices installed o

Strany 42

BIOS Setup 3-23 3.2.8. Frequency Control This item enables you to set the clock speed and system bus for your system. The clock speed and system bus

Strany 43

3-24 Chapter 3 Press <Y> and then <Enter> to install the defaults. Press <N> and then <Enter> to not install the defaults. The

Strany 44

BIOS Setup 3-25 3.2.12. 3.2.13. Save & Exit Setup Option Highlight this item and press <Enter> to save the changes that you have made in th

Strany 45 -  IRQ Resources

Introduction 1-1 Chapter 1. Introduction 1.1. Features & Specifications CPU • Designed for Intel® 90nm Pentium 4/Celeron D LGA775 Processors wi

Strany 46 - 3.2.7. PC Health Status

3-26 Chapter 3 SG-80 Series

Strany 47 - 3.2.8. Frequency Control

Driver Installation 4-1 Chapter 4. Driver Installation All the necessary drivers are included within the Drivers & Utilities CD that came packag

Strany 48

4-2 Chapter 4 4.1. Setup Items • Drivers Install the drivers for Windows Operating System. • Manual View the user’s manual in PDF file. • Utility C

Strany 49 - Exit Without Saving

How to Get Technical Support A-1 Appendix A. How to Get Technical Support (From our website) http://www.abit.com.tw (In North America) http://www.ab

Strany 50 - 3-26 Chapter 3

A-2 Appendix A alt.comp.periphs.mainboard.abit comp.sys.ibm.pc.hardware.chips alt.comp.hardware.overclocking alt.comp.hardware.homebuilt alt.comp.hard

Strany 51

How to Get Technical Support A-3 North America and South America ABIT Computer (U.S.A.) Corporation 45531 Northport Loop West, Fremont CA, 94538, U

Strany 52 - 4.1. Setup Items

A-4 Appendix A  Technical Support Form  Company Name:  Phone Number:  Contact Person:  Fax Number:  E-mail Address: Model * BIOS ID #

Strany 53

1-2 Chapter 1 Back Panel I/O • 1x PS/2 Keyboard, 1x PS/2 Mouse • 1x Serial Port, 1x Parallel Port, 1x VGA connector • 4x USB 2.0, 1x RJ-45 LAN Conn

Strany 54

Introduction 1-3 1.2. Layout Diagram (SG-80) User’s Manual

Strany 55

1-4 Chapter 1 1.3. Layout Diagram (SG-81) SG-80 Series

Strany 56 -  Technical Support Form

Introduction 1-5 1.4. Jumpers & Connectors Description Jumpers Description Default Setting CCMOS CMOS Memory Clearing Header Pins 2-3 Closed (

Příbuzné modely SG-80

Komentáře k této Příručce

Žádné komentáře